Regulation 2010/1003 - Type-approval requirements for the space for mounting and the fixing of rear registration plates on motor vehicles and their trailers and implementing Regulation 661/2009 concerning type-approval requirements for the general safety of motor vehicles, their trailers and systems, components and separate technical units intended therefor - Main contents
Please note
This page contains a limited version of this dossier in the EU Monitor.
Contents
official title
Commission Regulation (EU) No 1003/2010 of 8 November 2010 concerning type-approval requirements for the space for mounting and the fixing of rear registration plates on motor vehicles and their trailers and implementing Regulation (EC) No 661/2009 of the European Parliament and of the Council concerning type-approval requirements for the general safety of motor vehicles, their trailers and systems, components and separate technical units intended therefor Text with EEA relevance| Legal instrument | Regulation |
|---|---|
| Number legal act | Regulation 2010/1003 |
| CELEX number i | 32010R1003 |
| Document | 08-11-2010 |
|---|---|
| Publication in Official Journal | 09-11-2010; Special edition in Croatian: Chapter 13 Volume 036,OJ L 291, 9.11.2010 |
| Effect | 29-11-2010; Entry into force Date pub. +20 See Art 4 |
| End of validity | 05-07-2022; Repealed by 32019R2144 |
9.11.2010 |
EN |
Official Journal of the European Union |
L 291/22 |
COMMISSION REGULATION (EU) No 1003/2010
of 8 November 2010
concerning type-approval requirements for the space for mounting and the fixing of rear registration plates on motor vehicles and their trailers and implementing Regulation (EC) No 661/2009 of the European Parliament and of the Council concerning type-approval requirements for the general safety of motor vehicles, their trailers and systems, components and separate technical units intended therefor
(Text with EEA relevance)
THE EUROPEAN COMMISSION,
Having regard to the Treaty on the Functioning of the European Union,
Having regard to Regulation (EC) No 661/2009 of the European Parliament and of the Council of 13 July 2009 concerning type-approval requirements for the general safety of motor vehicles, their trailers and systems, components and separate technical units intended therefor (1), and in particular Article 14 (1)(a) thereof,
Whereas:
(1) |
Regulation (EC) No 661/2009 is a separate Regulation for the purposes of the type-approval procedure provided for by Directive 2007/46/EC of the European Parliament and of the Council of 5 September 2007 establishing a framework for the approval of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles (Framework Directive) (2). |
(2) |
Regulation (EC) No 661/2009 repeals Council Directive 70/222/EEC of 20 March 1970 on the approximation of the laws of the Member States relating to the space for mounting and the fixing of rear registration plates on motor vehicles and their trailers (3). The requirements set out in that Directive should be carried over to this Regulation and, where necessary, amended in order to adapt them to the development of scientific and technical knowledge. |
(3) |
Regulation (EC) No 661/2009 lays down fundamental provisions on requirements for the type-approval of motor vehicles and their trailers with regard to the space for mounting and the fixing of rear registration plates. Therefore, it is necessary to also set out the specific procedures, tests and requirements for such type-approval. |
(4) |
The measures provided for in this Regulation are in accordance with the opinion of the Technical Committee – Motor Vehicles, |
HAS ADOPTED THIS REGULATION:
Article 1
Definitions
For the purposes of this Regulation, the following definitions shall apply:
(1) |
‘vehicle type with regard to the space for mounting and the fixing of rear registration plates’ means vehicles which do not differ in such essential respects as:
|
(2) |
‘virtually flat surface’ means a surface of solid material, which may also consist of patterned mesh or grille, with a radius of curvature of at least 5 000 mm. |
(3) |
‘surface of patterned mesh’ means a surface consisting of an evenly spread pattern of shapes such as round, oval, diamond, rectangular or square holes spread evenly at intervals not exceeding 15 mm. |
(4) |
‘surface of grille’ means a surface consisting of parallel bars which are spread evenly and have a mutual distance of not exceeding 15 mm. |
(5) |
‘nominal surface’ means the theoretical geometrically perfect surface without taking into account surface irregularities such as protrusions or indentations. |
(6) |
‘longitudinal median plane of the vehicle’ means the plane of symmetry of the vehicle or, if the vehicle... |
More
This text has been adopted from EUR-Lex.
This dossier is compiled each night drawing from aforementioned sources through automated processes. We have invested a great deal in optimising the programming underlying these processes. However, we cannot guarantee the sources we draw our information from nor the resulting dossier are without fault.
This page is also available in a full version containing the summary of legislation, de geconsolideerde versie, the legal context, de Europese rechtsgrond, other dossiers related to the dossier at hand and finally the related cases of the European Court of Justice.
The full version is available for registered users of the EU Monitor by ANP and PDC Informatie Architectuur.
The EU Monitor enables its users to keep track of the European process of lawmaking, focusing on the relevant dossiers. It automatically signals developments in your chosen topics of interest. Apologies to unregistered users, we can no longer add new users.This service will discontinue in the near future.